BFT Gate Parts & Welding Nationwide

BFT Gate Parts & Welding in Kennedale: What to Know First

If your BFT gate is sagging, dragging, or refusing to close, we can usually get the parts and welding done within a few days, often in a single visit. As an independent BFT service provider in Kennedale, we replace hinges, posts, rails, rollers, and latches on BFT swing and slide gates, and we weld what’s broken or worn. You’ll get a written, upfront price before we touch a bolt, and every job is covered by our 90-Day Done Right Promise.

Call (817) 286-7391

This page is for Kennedale homeowners who own a BFT gate and need straight answers about parts, welding, and what it costs. If you’d rather just talk it through, call (817) 286-7391 and a live person answers, day or night.

How BFT Products Fail - and How We Fix Them

BFT makes a solid operator. The motor side of their swing and slide systems is well engineered. Where we get called in Kennedale is the metal: the parts that carry the weight, take the wind, and wear out slow until one day they don’t.

• BFT swing gate hinges on heavier leafs. The BFT Aries and Deimos swing operators are strong, but the hinge hardware on a 14 or 16-foot gate takes punishment the motor never sees. When a Kennedale gate starts to sag and the operator strains, the problem is usually a worn hinge pin or a stretched hinge plate, not the motor. We cut out the old hinge, weld in a heavier replacement, and the operator stops working so hard.
• BFT slide gate rollers and track wear on the BFT IGEA and Thalia lines. Slide gates ride on steel rollers that grind against the track every time the gate moves. After enough years, the rollers flat-spot or the track develops a groove, and the gate starts to shimmy. We replace rollers with sealed-bearing units and weld in new track sections where the metal has worn thin. The operator lasts longer when the rolling surface is true.
• Post failure at the operator mounting point. This one shows up more in Texas clay than anywhere else. The post that holds the BFT operator or the gate’s end post shifts with the soil, the welds crack, and the gate goes out of square. We dig down, inspect the footing, weld in a new post, and reinforce the mount. Victor Salinas has pulled more than one post out of Kennedale ground that looked fine above grade and was rusted through below it.
• Latch and lock misalignment on BFT swing gates. When a swing gate isn’t latched square, the operator’s limit switches work overtime and the gate slams or stalls. The fix is often a weld: building up the latch plate, repositioning the catch, or replacing the strike entirely. We set the latch so the gate closes soft and the BFT controller reads it correctly.
• Cracked or broken gate frame welds. BFT operators are quiet enough that a cracked weld on the gate frame can go unnoticed for months. The motor keeps working, but the frame flexes at the crack with every cycle. Eventually the weld fails completely and the gate twists. We grind out the old weld, bevel the joint, and lay in a full-penetration weld with proper heat. The repair is stronger than the original factory weld, which is not something we say lightly.

Our BFT Gate Parts & Welding Process

Every BFT job follows the same sequence, whether it’s a hinge replacement or a cracked rail. Here’s how it goes:

1. 1
   You call (817) 286-7391. A live person answers and asks what the gate is doing: sagging, grinding, stalling, not latching. We schedule the visit.
2. 2
   We inspect the whole gate, not just the symptom. On a BFT swing gate, we check hinges, posts, the operator mount, the latch, and the controller’s limit settings. On a slide gate, we inspect the rollers, track, guide wheels, and end stops. The part that’s broken is not always the part that’s causing the problem.
3. 3
   We quote the repair in writing, before work starts. You’ll know the parts cost, the welding time, and exactly what we’re going to do. If we recommend an OEM BFT part, we’ll tell you why. If a quality aftermarket part will do the job just as well for less, we’ll say that too and let you decide.
4. 4
   We do the work. Welding is done on-site. We clean the area, grind the joint, weld, and dress the weld smooth. No pigeon droppings, no slag on your driveway.
5. 5
   We test the gate under its own operator. The BFT controller gets a full cycle test. We set the limits, check the safety edges, and run the gate through a full open and close at normal speed. If the gate’s not working right, it’s not done.
6. 6
   We walk you through the repair and hand you the warranty. Our 90-Day Done Right Promise covers every BFT repair, in writing. If something isn’t right, we come back and make it right.

What BFT Gate Parts & Welding Costs in Kennedale

Here are honest ranges for the BFT gate parts and welding work we do in Kennedale. These are typical numbers, not a quote. Your exact price depends on gate size, damage, and which BFT model you have.

• Hinge replacement (single swing gate, standard steel hinge): $180-$420
• Post replacement with welding (swing or slide gate end post): $450-$1,200 depending on post size and footing condition
• Slide gate roller and track repair: $220-$650
• Custom welding repair (cracked frame, broken rail, latch rebuild): $150-$800 depending on scope
• Latch and lock replacement or realignment: $120-$350

What moves the price: gate weight and length, whether the post footing needs redoing, how much cutting and grinding the weld requires, and whether the part must come from BFT or can be substituted with a quality aftermarket equivalent. You’ll always see the number before we begin. Call (817) 286-7391 for a free estimate on your BFT gate repair.

Why Kennedale Homeowners Call Ironworks Gate Co. for BFT Work

We’ve been doing this since 1984. Not gate work as a side line. Gate work as the whole job. Our techs work on nine automation brands including BFT, LiftMaster, Mighty Mule, Ghost Controls, and DoorKing, which matters when a Kennedale home has a mixed setup. A background-checked, uniformed technician arrives when we say, quotes the repair before any work starts, and stands behind it with our written 90-Day Done Right Promise. If you’re a senior or veteran, we take 5% off, always. Most BFT parts and welding jobs are done in one visit, and the price you’re quoted is the price you pay, no surprises.

FAQs