Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterDoorKing Gate Access Control in Kennedale: What to Know First
DoorKing gate access control repair in Kennedale typically runs between $190 and $485 depending on whether it’s a keypad, phone entry board, or receiver that’s failed, and most repairs are completed in one visit. We’re an independent DoorKing service provider, not a factory authorized shop, which means we tell you straight whether a part can be salvaged or needs replacing without any pressure to upsell. This page is for the Kennedale homeowner whose DoorKing keypad stopped beeping, whose remote stopped reaching the gate, or whose phone entry won’t ring the house anymore. Call (817) 286-7391 and a live person answers, day or night.
How DoorKing Products Fail - and How We Fix Them
DoorKing builds solid equipment, but Kennedale’s heat and dust find every weak point sooner or later. Here’s what we see on actual service calls, not in a manual.
- DoorKing 1812 keypads with dead or stuck buttons. The 1812 series has been on Kennedale driveways for years, and we regularly replace the internal membrane switch when buttons quit responding. Texas sun breaks down the rubber over time. The board underneath is usually fine, which means a $60 part instead of a $400 keypad.
- DoorKing 1815 telephone entry systems losing the dial tone. This model relies on an internal relay that wears out, and when it goes, the unit stops calling the house line. We’ve also found that Kennedale’s occasional storms put a surge through phone lines that fries the relay before anything else. We test the relay first, then the wiring, and only then consider swapping the board.
- DoorKing MicroCLICK remotes that stop reaching the gate. Most of the time it’s not the remote. The receiver antenna on the gate gets bent, corroded, or knocked out of position by wind and lawn mowers. We straighten it, clean the connection, and test with a fresh battery – that clears a surprising number of “dead remote” calls without selling you a new transmitter.
- DoorKing access control circuit boards with blown fuses. Kennedale runs on overhead power lines, and a near lightning strike or transformer flicker will take out the fuse before it reaches the main board. DoorKing boards are built to sacrifice the fuse. We replace it, test the board, and explain how a surge arrestor mounted at the operator can keep it from happening again.
- DoorKing slide gate readers losing programming after power outages. The older DoorKing units use a battery-backed memory that eventually gives out, and when the power blinks, all the keypad codes are gone. We document your existing codes before touching anything, so re-entering them takes minutes instead of you hunting for that sticky note from 2016.
Our DoorKing Gate Access Control Process
Every DoorKing job follows the same quiet routine, and you’ll know the price before we turn a single screw.
- 1
We listen first. You tell us what the keypad, remote, or entry system is doing and when it started. Half the diagnosis is in the story.
- 2
We inspect the components. DoorKing access control lives in the operator box, the keypad housing, and the wiring between them. We check power, fuses, connections, and the board itself.
- 3
We quote the repair. You get a written price for parts and labor while we stand there. No surprises after the fact, ever.
- 4
We fix it right the first time. We stock common DoorKing parts and have a local source for the rest. OEM when it matters for warranty and fit, quality aftermarket when it saves you real money and works just as well.
- 5
We test everything. Keypad codes, remote range, phone entry ring-through, safety edges, and the gate’s full open-close cycle.
- 6
We walk you through it. You see it work before we leave, and the 90-Day Done Right Promise covers the whole job in writing.
What DoorKing Gate Access Control Costs in Kennedale
Here are honest numbers for the DoorKing work we see most often in Kennedale, taken from our own service records.
- Keypad or button repair (1812 series): $190 to $290
- Remote receiver repair or antenna replacement: $140 to $220
- Telephone entry relay replacement: $180 to $310
- Circuit board fuse replacement and surge test: $110 to $180
- Full access control system replacement (keypad, receiver, and wiring integration): $750 to $1,400
- Complete new DoorKing installation including operator and access control: $2,800 to $5,500
The range depends on whether we can repair a component or need to replace it, how far the wiring runs from the house to the gate, and which DoorKing model is already on the post. Every estimate is free, and the price you’re quoted is the price you pay. Call (817) 286-7391 for an exact number on your gate.
Why Kennedale Homeowners Call Ironworks Gate Co. for DoorKing Work
We’ve been serving this area for over 42 years, and Victor Salinas grew up here, not far from the old Kennedale Stockyards grounds. When a DoorKing gate access system is down, it means you can’t get in your own driveway without getting out of the truck and wrestling a gate open. We treat that with the urgency it deserves. Our technicians are trained on DoorKing equipment and also service LiftMaster, Mighty Mule, Ghost Controls, and six other gate-automation brands, so the right fix happens on the first visit no matter what’s mounted on the post. Every job is backed by the 90-Day Done Right Promise: written, no paperwork, no arguing. If the gate’s not working right, it’s not done.
FAQs
No. We’re an independent DoorKing service provider. That independence means we recommend the repair that makes sense for you, not the one that protects a factory warranty or pushes a new unit. We service DoorKing equipment every week and know these systems as well as anyone in Tarrant County.
Most DoorKing access control calls are scheduled within one to two business days, and a live person answers the phone 24 hours a day, 7 days a week when you call (817) 286-7391. If your gate is stuck open or your keypad is completely dead, tell us when you call and we’ll make it a priority.
Both, and we’ll tell you which we’re using and why. For circuit boards, relays, and components covered under an existing DoorKing warranty, we use OEM parts so the warranty stays intact. For older models where the OEM part costs three times more and offers no practical advantage, a quality aftermarket part often makes better sense.
Intermittent keypad behavior usually points to a failing membrane switch, a loose wire connection behind the keypad, or moisture getting into the housing. Kennedale’s temperature swings swell and shrink the housing, and humidity creeps in through hairline cracks. We trace which failure applies to your unit and fix it before it becomes a complete outage.
If your DoorKing operator is older than 15 years and multiple components are failing, replacement may be the better long-term call. But most access control failures are isolated to one part, and a repair between $190 and $485 keeps your system running for years. We’ll give you our honest recommendation and never push a replacement you don’t need. Call (817) 286-7391 for a free estimate.
Written by Victor Salinas, Owner & Gate Repair Specialist, Ironworks Gate Co. at Ironworks Gate Co., serving Kennedale and nearby areas.