DoorKing Gate Installation Nationwide

DoorKing Gate Installation in Kennedale: What to Know First

We install and service DoorKing gate operators throughout Kennedale, from single swing gates off Mansfield Cardinal Road to double slide gates on larger acreage off Dick Price Road. A typical DoorKing gate installation runs $1,800 to $4,200 depending on operator model, gate size, and power run distance, and most jobs are completed in one visit. The price is quoted and agreed before a single bolt is turned, so there are no surprises on the bill.

Call (817) 286-7391

If you own a DoorKing operator and the gate won’t move, the keypad quit talking to the board, or the motor hums but the gate sits still, this page will tell you exactly what you’re dealing with. We’re an independent DoorKing service provider, not a factory-authorized dealer, which means we buy parts where they’re best for you and we warranty our work in writing. Call (817) 286-7391 and a real person answers, day or night.

How DoorKing Products Fail - and How We Fix Them

DoorKing builds a solid operator. We’ve worked on hundreds of them from the 9150 slide series to the 6002 swing arm models that show up all over Kennedale’s older subdivisions. But every brand has its habits. These are the five we see most on DoorKing installation and call-back work.

• Limit switch drift on 9150 slide operators. The mechanical limit nuts on DoorKing slide units loosen over time, especially on gates that cycle many times a day. The gate starts stopping short of fully closed, then a week later it’s over-traveling and slamming the stop. We see this constantly on properties off New Hope Road. The fix is re-setting the limits and adding a thread-lock so they hold. If the limit shaft is worn, we replace it rather than patching it, because a drifted limit switch is how gates end up off their track.
• Control board failure after electrical storms. Kennedale gets serious lightning in the spring, and DoorKing’s older 4503 and 6003 boards are sensitive to power surges. Homeowners call us because the gate is dead after a storm and they assume the motor is fried. More often the motor is fine and the board took the hit. We install surge protection on the power feed and a shielded low-voltage run as part of any DoorKing installation we do now. It’s a small add that saves a $400 board replacement later.
• Capacitor failure on swing gate operators. The DoorKing 6002 and 6100 swing arms use a start capacitor that weakens with age. The gate hums but doesn’t move, or it only opens halfway before giving up. A weak capacitor often gets misdiagnosed as a bad motor by less experienced techs. We test the capacitor with a meter before touching the motor. It’s a $30 part versus a $600 motor, and we’d rather tell you the honest diagnosis than sell you parts you don’t need.
• Gearbox wear on the 9150 and 9250 slide models. The bronze drive gear inside the gearbox is designed to be the sacrificial part, and on 15-year-old operators it’s often chewed down to nubs. The gate jerks, hesitates, or makes a grinding sound. DoorKing sells the gear as part of a larger assembly, but we keep an aftermarket gear on the truck that costs a third of OEM and lasts just as long in the North Texas heat.
• Photo eye and safety edge alignment problems. On any DoorKing job where the gate reverses for no reason or refuses to close, the first thing we check is the photo eye alignment and the edge sensor continuity. Kennedale’s clay soil shifts with moisture, and concrete posts settle. A photo eye that was perfectly aligned two years ago can be two inches out of line now. We re-level the posts or shim the mounting bracket so the beam holds.

Our DoorKing Gate Installation Process

Every DoorKing job we take follows the same honest sequence. No shortcuts, no mystery charges, no coming back twice for something we could have handled the first visit.

1. 1
   You call, we listen. A live person answers. We ask what the gate is doing or not doing, what model operator you have if you know it, and when it started. Then we schedule a time that works.
2. 2
   We show up and test. Our technician arrives background-checked and in uniform. We check voltage at the operator, test the capacitor and board, inspect the gearbox, rails, hinges, and safety sensors. On an install, we measure the gate weight, post depth, and power run distance before quoting anything.
3. 3
   Straight diagnosis and a written price. We tell you what we found, what we recommend, and what it costs. The price is settled before work begins. If an OEM DoorKing part is backordered, we give you the option of a quality aftermarket part with our warranty behind it.
4. 4
   The work gets done. Install, repair, or retrofit. We run power properly in conduit, set limits correctly, and wire the safety edges so they actually stop the gate. We use copper wire, proper gauge, and connectors rated for outdoor exposure.
5. 5
   We test it like we won’t be back. We run the gate through full open-close cycles, check every sensor, and verify the keypad and remotes. If it’s not right, we keep working until it is. Victor’s rule applies: if the gate’s not working right, it’s not done.
6. 6
   We walk you through it. We show you how to set remotes, program the keypad, and what the LED lights on the board mean so you know if something needs attention. Then we hand you the 90-Day Done Right Promise in writing.

What DoorKing Gate Installation Costs in Kennedale

Gate work is priced by the job, not by the hour, and every quote is settled before we start. Here are honest ranges for the DoorKing jobs we handle in Kennedale:

• Single swing gate with new DoorKing 6002 operator: $1,800 to $2,600 installed, depending on post condition and power access.
• Double swing gate with 6100 operator: $2,800 to $4,000, including new hinges and proper gate alignment if needed.
• Sliding gate with new DoorKing 9150 operator and rail work: $2,400 to $4,200, depending on rail condition, gate weight, and power distance.
• Pedestrian gate with keypad and electric strike: $900 to $1,500 installed.
• Control board replacement on existing operator: $350 to $550 with labor, OEM or quality aftermarket.
• Capacitor replacement on 6002/6100 swing models: $120 to $190 installed.

What moves the number: gate weight and condition, post integrity, how far we need to run power, and whether we’re replacing the operator or building a fresh install. If you have an existing written estimate from another company, bring it in. Our free second opinion offer means we’ll look at it honestly and tell you if it’s fair or inflated. Call (817) 286-7391 for a free estimate on your DoorKing gate installation.

Why Kennedale Homeowners Call Ironworks Gate Co. for DoorKing Work

We’ve been doing gate work in this area for over 42 years, and we plan on being here another forty. That matters when you’re trusting someone to install a gate that protects your home and everything behind it. Victor Salinas grew up in Kennedale, not far from the old Kennedale Stockyards grounds, and he’s spent his working life within a few miles of where he was raised. When neighbors call about a DoorKing operator that quit on a Sunday afternoon, he shows up because that’s how this company has always worked.

Every job we complete carries our written 90-Day Done Right Promise. If something isn’t right after we leave, we come back and make it right. No paperwork, no arguing, no exceptions. We’re also trained and equipped on nine gate-automation brands, so if your property has a DoorKing on the driveway and a Mighty Mule or Ghost Controls on a back gate, one call covers all of it. And if we recommend replacing a DoorKing operator, we can show you honest options from LiftMaster or Linear if that fits your gate better. We sell what’s right for the job, not what’s left on our truck.

FAQs