Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterDoorKing Gate Motor & Opener in Kennedale: What to Know First
DoorKing gate motor and opener service in Kennedale typically runs between $275 and $900 depending on what failed, and most repairs are completed in a single visit. We’re an independent DoorKing service provider, meaning we fix what’s actually wrong rather than selling you a replacement you don’t need. If you’ve got a DoorKing swing or slide motor acting up, call (817) 286-7391 and we’ll give you a straight answer on cost before any work begins.
This page is for Kennedale homeowners who own a DoorKing gate system, or inherited one with the house, and want to know what it’ll take to get it working right again. Not a thick brochure. Just the facts from 42 years of gate work in Tarrant County.
How DoorKing Products Fail And How We Fix Them
DoorKing builds durable equipment, but every brand has its habits. Here are the failures we see regularly on Kennedale driveways, and the real cause behind each one:
- DoorKing 9150 slide gate opens halfway, then reverses. Nine times out of ten, this is a worn drive chain or a slipping chain idler pulley, not the motor itself. The safety loop sees the gate stall and orders it back. We replace the chain and tension it to factory spec instead of selling you a new operator.
- DoorKing 6002 swing gate hums but won’t budge. That hum is the motor trying, but the gearbox has stripped. The 6002 series uses a nylon drive gear that sacrifices itself to protect the motor. We replace the gear and inspect the output shaft for play. You keep your original operator, and the bill stays under $500 most of the time.
- DoorKing 9050 slide motor cranks fine but the gate jerks on startup. Kennedale’s black clay soil swells and shrinks with the seasons, which shifts steel posts and asks the gate to run slightly out of square. Over time that binds the rollers and stresses the motor. We realign the gate, replace flat wheel bearings, and reset the torque limiter so the motor isn’t fighting the frame.
- DoorKing MicroPlus keypad or phone entry stops triggering the motor. The motor’s often fine. The problem is a failed relay on the control board, frequently from a lightning strike or a power surge. DoorKing boards are repairable to a point, but if the board is burned, we quote an OEM replacement and explain exactly what that part will cost, no mystery line items.
- DoorKing 1602 operator runs, then the gate coasts past its limit. That’s a dead magnetic limit switch. They sit inside the operator chassis and gather dust and spiderwebs over a decade. We clean the housing, test the switch with a meter, and replace it with the OEM part so the gate stops exactly where it should, every cycle.
One thing our techs always check on a DoorKing job: the battery backup terminals. DoorKing operators are tough on their own batteries when the terminals corrode, and Kennedale humidity pushes that corrosion along. A five-minute terminal cleaning can add years to a motor that otherwise runs fine.
Our DoorKing Gate Motor & Opener Process
Every DoorKing job we take follows the same unhurried order of operations. No short cuts, no skipping steps.
- 1
We answer the phone. You get a live person, not a voicemail. We ask what the gate is doing, or not doing, and schedule a time that fits your day.
- 2
We diagnose before we quote. Our technician arrives in a stocked truck, runs the operator through its cycle, checks motor draw, limit switches, and control board health. Then we give you an upfront price, agreed to before any wrench turns.
- 3
We make the parts call honestly. On DoorKing systems, critical moving parts and boards get OEM components. For belts, chains, and batteries, we’ll tell you if a quality aftermarket part will serve you just as well for less money, and we let you choose.
- 4
We do the repair once. The fix gets done the same visit whenever parts are on the truck, which they are for most DoorKing failures.
- 5
We test, then test again. The gate gets cycled repeatedly, the limits get confirmed, and the safety loops get checked with a metal object, not a theory.
- 6
We hand you the warranty in writing. The 90-Day Done Right Promise covers every job. If it’s not right, we come back and make it right. No paperwork, no arguing.
What DoorKing Gate Motor & Opener Costs in Kennedale
Here are honest dollar ranges for the DoorKing repairs we see most in Kennedale:
- Limit switch replacement: $180 to $280
- Drive chain and idler pulley replacement on a 9150: $250 to $400
- Gearbox replacement on a 6002 swing operator: $320 to $480
- Control board relay repair or replacement: $220 to $600, depending on board condition
- Full operator replacement including new motor and mounting hardware: $850 to $1,900, quoted in writing before the work starts
What moves the price: how long the gate has been running out of adjustment, whether the posts have shifted, and whether past repair work left damaged wiring behind. Whatever the estimate, the number we quote is the number you pay. We don’t start a job without a written, agreed price. Call (817) 286-7391 for a free estimate on your DoorKing system.
Why Kennedale Homeowners Call Ironworks Gate Co. for DoorKing Work
Victor Salinas grew up in Kennedale, not far from the old stockyards grounds, and he’s been working on gate systems around Tarrant County for most of his adult life. He trained in welding and industrial mechanics at Tarrant County College’s Southeast Campus, and he approaches every DoorKing operator the way his father, a welder, approached a bead: measure twice, weld once. When a slide motor quits or a swing gate binds, neighbors call us because we show up and fix it correctly the first time.
We service DoorKing every week, but we’re also trained and equipped on LiftMaster, Mighty Mule, Ghost Controls, and five other brands. If your system is a DoorKing motor with a Ghost Controls keypad, we don’t blink. We fix the whole gate, not just the nameplate.
Everything we do is backed by the 90-Day Done Right Promise. If it’s not right, we come back and make it right. That’s the Keystone Standard, applied to every job from a hinge replacement to a full operator swap. A live person answers every call, 24 hours a day, 7 days a week, and every technician who comes to your property is background-checked and in uniform. If the gate’s not working right, it’s not done.
FAQs
No. As an independent DoorKing service provider, our repairs use OEM or equivalent parts and we never alter the original design. If your operator is still under DoorKing’s warranty, we’ll tell you before we touch anything whether the repair should go through the manufacturer instead of through us. Your warranty stays intact either way.
Yes, in most cases. DoorKing keeps parts available for operators going back decades, and we maintain accounts that let us source OEM boards, limit switches, and gearboxes without waiting weeks. For discontinued parts, we know which aftermarket alternatives actually hold up on a Texas driveway.
That’s usually the MicroPlus or access control receiver losing its programming, or a shorted keypad wire. The motor and receiver are fine. We can reprogram the keypad, re-run the wire if critters chewed it, or replace the keypad face for a fraction of a new operator. Call (817) 286-7391 and we’ll talk through what your system is doing before we even schedule.
Most Kennedale calls get same-day or next-day service, and we answer the phone 24 hours a day, 7 days a week. If your gate is stuck shut and you can’t get a car in or out, tell the dispatcher and we’ll make time that day.
If the motor itself tests good and the problem is a gear, chain, board, or switch, repair almost always makes sense. If the operator is over 15 years old, the motor windings are failing, and the gearbox is worn, replacement costs less in the long run. We’ll show you the meter readings and let the numbers make the decision. Estimates are free.
Contact Ironworks Gate Co. for DoorKing Gate Motor & Opener in Kennedale
Call (817) 286-7391 for a free estimate on any DoorKing gate motor or opener issue. A live person answers, the price is agreed before we start, and every job is backed by the 90-Day Done Right Promise. From a sticky limit switch to a full operator replacement, we’ll make your DoorKing gate run like it should.
Written by Victor Salinas, Owner & Gate Repair Specialist, Ironworks Gate Co. at Ironworks Gate Co., serving Kennedale and nearby areas.