Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterDoorKing Gate Parts & Welding in Kennedale: What to Know First
DoorKing gate parts and welding repair in Kennedale typically runs $180 to $640 depending on whether we are replacing a hinge, rebuilding a post, or welding a cracked rail. We are an independent DoorKing service provider, not a factory-authorized shop, and most parts jobs are completed in a single visit because our trucks carry the hinge sets, rollers, and steel stock these systems actually need. If your DoorKing gate is sagging, grinding, or refusing to close, call (817) 286-7391 and a live person will answer, day or night.
This page is for Kennedale homeowners who own a DoorKing swing or slide gate and need straight answers about parts, welding, and what it costs to make the gate right again. It is written by Victor Salinas, who grew up near the old Kennedale Stockyards grounds and has been fixing gate metal in this town for decades. No phone trees, no guesswork, no invoice surprises.
How DoorKing Products Fail - and How We Fix Them
DoorKing builds a solid operator, but the metal around it takes a beating in Texas. Here are the failures we see most often on DoorKing systems in Kennedale, and what we do about them.
- Worn hinge pins on the 6000-series swing gates. DoorKing’s 6002 and 6100 swing operators pull a lot of weight through two hinge points. Over five or six Texas summers the pin wears oval and the leaf drops half an inch, which throws the load off the operator and burns out limit settings. We replace the hinge set, re-shim the leaf, and reset the travel so the motor is not fighting the sag.
- Cracked welds at the post base on slide gates. Kennedale soil is expansive clay. It swells after rain and shrinks in August, and that movement flexes slide gate posts at the weld line. We regularly see the base fillet cracked halfway around on DoorKing 9050 and 9150 slide installations. We cut out the old weld, re-plate the base with a gusset, and weld it hot enough to hold through the next decade of soil movement.
- Flat-spotted rollers on the 9000-series track. DoorKing slide gates ride on steel rollers that wear flat on the bottom after years of dust and grit working into the bearings. A flat roller makes the gate shudder and, eventually, trips the obstruction sensor and reverses mid-cycle. We swap the rollers, clean the track, and check the guide posts so the gate rolls quiet instead of grinding.
- Latch and lock misalignment after post shift. The mag-lock or mechanical latch on a DoorKing gate only lines up if the gate and the catch post have not moved. In Kennedale, posts move. The gate closes fine but the lock chatters and the operator faults out. We realign or rebuild the catch post, then set the lock gap to factory spec so the lock engages without the operator ramming it.
- Bent or bowed gate leaves from wind load. A solid-panel DoorKing gate in an open Kennedale yard catches north wind like a sail. We see top rails bowed and mid-rail welds popped on wide double-leaf gates. We straighten what is salvageable, reinforce the rail with a brace channel, and weld the seams so the gate does not flex against the operator’s thrust.
Our DoorKing Gate Parts & Welding Process
When a DoorKing owner calls us from Kennedale, here is how the job goes from first ring to final test.
- 1
You call (817) 286-7391. A live person answers, asks what the gate is doing, and schedules a visit window that we actually keep. No automated menu.
- 2
We inspect the gate and the operator together. We check hinges, posts, rollers, welds, and the opener’s force settings. DoorKing operators have diagnostics built in, and we read them before we touch a wrench.
- 3
We show you what failed and quote the fix before any work starts. You get a written price for parts and labor, agreed up front. No surprises on the bill, ever.
- 4
We make the repair. For metal work we use OEM DoorKing parts when the job calls for them, and quality American-made aftermarket steel when it is stronger for less money. We will tell you which is which and why.
- 5
We test the gate through full cycles. Open, close, obstruction test, lock engagement. We run it until it behaves, then we run it again.
- 6
We walk you through what we did and leave the job clean. Every DoorKing repair carries our 90-Day Done Right Promise in writing. If it is not right, we come back and make it right. That is the Keystone Standard on every job.
What DoorKing Gate Parts & Welding Costs in Kennedale
Here are the price ranges we quote most often for DoorKing metal and parts work in Kennedale. Every quote is written and agreed before we start, so the final bill matches the number you approved.
| DoorKing Job | Typical Price Range | What Moves the Price |
|---|---|---|
| Hinge replacement (single leaf) | $180 - $320 | Leaf weight, weld condition, shimming needed |
| Post replacement or rebuild | $350 - $640 | Dig depth, concrete work, steel gauge |
| Slide gate roller replacement | $160 - $280 | Roller count, track condition |
| Rail repair or reinforcement welding | $200 - $450 | Crack extent, access, brace steel |
| Latch and lock realignment | $140 - $260 | Post shift severity, lock type |
| Custom welding (brackets, gussets, gates) | $150 - $500+ | Scope, steel, design time |
Call (817) 286-7391 for a free estimate. We will come out, look at your DoorKing gate, and give you a written number before a single weld is struck.
Why Kennedale Homeowners Call Ironworks Gate Co. for DoorKing Work
Kennedale is not a big town, and word gets around fast. We have been doing gate work here for over 42 years, since 1984, and the reason people keep calling is simple: we show up when we say we will, we fix the gate correctly, and we stand behind it in writing. Victor Salinas trained in welding and industrial mechanics at Tarrant County College’s Southeast Campus and has spent his working life within a few miles of where he was raised. He is the guy neighbors call when a swing gate will not close right, because he treats every weld like his father taught him: measure twice, weld once.
Every technician who steps onto a Kennedale driveway is background-checked and uniformed, working in your home the way they would work in their own mother’s. We are trained and equipped on nine gate-automation brands, so if your DoorKing opener needs a part we do not have on the truck, we know exactly which supplier to call and how long it takes. And because we also service LiftMaster, Mighty Mule, and Ghost Controls, we can diagnose a mixed-brand setup without scrambling. If the gate is not working right, it is not done.
FAQs
We are an independent DoorKing service provider, not a factory-authorized shop, so we cannot bill DoorKing for work under their warranty. What we do is use OEM DoorKing parts when the warranty matters, and we back every repair with our own 90-Day Done Right Promise in writing. Call (817) 286-7391 and we will tell you honestly whether a warranty claim is worth pursuing before you spend a dollar.
Our trucks carry the DoorKing hinge sets, rollers, and common hardware that Kennedale gates need most often, so most parts jobs are done same-visit. For specialty DoorKing components we order from established suppliers and usually have the part in hand within two to three business days. Call (817) 286-7391 and we will check availability while you are on the phone.
If the gate leaf is structurally sound, welding the cracked rail or replacing a worn hinge almost always costs less than a new gate and gets you another decade of service. If the leaf is rusted through or bowed beyond straightening, we will tell you that too, with a written quote for a replacement gate built to handle the DoorKing operator you already have. Call (817) 286-7391 for a straight answer, not a sales pitch.
We answer the phone 24 hours a day, 7 days a week, and for a gate that will not close or a leaf that has dropped, we typically can get a technician out the same day or first thing the next morning. Metal and welding jobs are scheduled properly, with a firm window and a live person on the phone if anything changes. We will be there when we say.
Yes. We regularly fabricate and weld custom brackets, reinforcement gussets, and gate modifications for DoorKing swing and slide systems in Kennedale. Victor Salinas was raised by a welder and the metal work is the part of the job we enjoy most. Call (817) 286-7391 with what you have in mind and we will give you a free measure and a written price.
Get Your DoorKing Gate Fixed Right in Kennedale
If your DoorKing gate is sagging, grinding, cracking, or refusing to close, call (817) 286-7391 now. A live person answers, 24 hours a day. We will schedule a visit, quote the work in writing before we start, and stand behind it with the 90-Day Done Right Promise. Free estimates, senior and veteran discounts always apply, and $50 off any repair over $250. Done right and backed in writing. That is how we do it in Kennedale.
Written by Victor Salinas, Owner & Gate Repair Specialist, Ironworks Gate Co. at Ironworks Gate Co., serving Kennedale and nearby areas.