Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGhost Controls Gate Installation in Kennedale: What to Know First
Ghost Controls gate installation in Kennedale typically runs $450 to $950 for a complete opener installation on an existing gate, and most jobs are finished in a single visit. We’re an independent Ghost Controls service provider, not a factory branch, which means we make repair-or-replace calls based on what’s actually wrong with your gate, not on what’s easiest to bill. If you own a Ghost Controls opener that won’t run, runs halfway, or never got installed correctly in the first place, call (817) 286-7391 and we’ll give you a straight answer and a firm price before any work begins.
This page is for homeowners in Kennedale and nearby Tarrant County who already own Ghost Controls equipment, or who are considering it and want to know what they’re getting into. Ghost Controls builds a solid opener, but installation details determine whether it works quietly for fifteen years or eats a control board every spring. We’ll walk you through what we see on Ghost Controls jobs here so you know what questions to ask.
How Ghost Controls Products Fail - and How We Fix Them
Ghost Controls openers share a design philosophy: lightweight residential hardware, battery backup, and a fairly simple control board. That simplicity is good, but it means a handful of installation mistakes show up over and over. Here’s what we actually find on Kennedale driveways:
- AXDP and AXD series units with “gate opens a few inches and stops.” This is almost never the motor. It’s the travel limit resetting because the opener lost its position after a power flicker. The fix is a full limit recalibration and confirming the gate’s mechanical balance, because a gate that’s binding at the hinge forces the board to work harder and resets the limits sooner.
- Ghost Controls TSS1 and TSS1XP solar units going dead on the north side of the house. Kennedale gets plenty of sun, but a gate set back under a carport or shaded by a mature oak will kill a solar panel’s output. We reposition the panel or add a second panel before blaming the battery, which saves owners the cost of a battery they didn’t need.
- Remote range that drops to ten feet. Ghost Controls receivers are sensitive to the board’s antenna placement. If the installer tucked the antenna inside a steel gate post or let it lie against the chassis, range collapses. We route the antenna externally and rerun the learn sequence, and range usually jumps back to thirty or forty feet.
- AXVS series on a double gate: one leaf lags behind. Ghost Controls dual-gate setups rely on a synchronized board and matched leaf weight. When one leaf is heavier, or a hinge is worn, the lighter leaf moves first and the opener reads a fault. We rebalance the leaves and set the opening delay correctly, which is an installation issue, not a product defect.
- Water intrusion in the control board housing after a spring storm. Kennedale’s spring downpours find their way into any housing that wasn’t sealed by the original installer. We replace the board if it’s corroded, then seal the housing with the drain holes pointed down, which is how the factory intended it and how most installations skip it.
The through-line: Ghost Controls hardware is sound. Most failures we fix are installation failures, not equipment failures. That’s why we spend as much time on the gate itself as we do on the opener.
Our Ghost Controls Gate Installation Process
Every Ghost Controls job follows the same sequence, whether it’s a fresh install or a repair. Here’s what happens when you call us in Kennedale:
- 1
Call and talk to a person. A live body answers at (817) 286-7391. We ask what the gate is doing, what model opener you have if you know it, and pick a time that actually works for you.
- 2
On-site diagnosis. We check the gate’s weight and swing first. A Ghost Controls opener on a gate that’s too heavy fails early, so we verify the mechanical side before touching the electronics.
- 3
Parts decision, made with you. If a board or arm needs replacing, we lay out OEM versus quality aftermarket choices with real-world lifespan differences and price differences. No hidden preference, no upcharge games.
- 4
The work. We install or repair the opener, set travel limits, program remotes and keypad, and adjust force settings so the gate closes firmly but reverses safely.
- 5
Full test cycle. We run the gate open and closed at least ten times, check safety reversal, test the battery backup if it has one, and watch for binding.
- 6
Walkthrough and written guarantee. Victor or the lead tech walks you through what was done, what to watch for, and the 90-Day Done Right Promise in writing. If it’s not right, we’re back.
Most Ghost Controls installations are done in one visit. If a part has to be ordered, we tell you that before we leave, and we don’t collect a deposit until the part is in our hands.
What Ghost Controls Gate Installation Costs in Kennedale
Here’s what we quote for the most common Ghost Controls jobs in Kennedale:
- Complete Ghost Controls opener install on an existing single swing gate: $450 to $700, including opener, arm, labor, and programming
- Dual swing gate opener install (AXDP or equivalent): $650 to $950, including synchronization and both arms
- Solar panel add-on or relocation (TSS1 series): $120 to $200
- Control board replacement with OEM board: $180 to $320 depending on model
- Full gate and opener install, new gate fabricated: $2,200 to $5,500, depending on gate size, style, and steel weight
What moves the price: gate weight, gate type (swing double is more labor than slide single), post condition, and whether the existing opener wiring is salvageable. The price we quote before work starts is the price on the invoice. No change orders, no surprise line items. Call (817) 286-7391 for an exact quote on your gate. Estimates are free, and we stand behind the number.
Why Kennedale Homeowners Call Ironworks Gate Co. for Ghost Controls Work
We’ve been working on gates in this part of Tarrant County since 1984. That’s four decades of seeing what happens to gate hardware when Texas heat, spring storms, and Kennedale’s clay soil all do their work on a steel post. Ghost Controls is one of nine opener brands our techs are trained on, along with LiftMaster, Mighty Mule, and DoorKing. That matters when someone wants to switch brands, or when a Ghost Controls board is backordered and a different brand’s opener would get the gate working faster.
Every job carries the 90-Day Done Right Promise. Written, no paperwork, no arguing. If the gate isn’t right, we come back and make it right. We answer the phone 24 hours a day, seven days a week, with a live person. And our techs are background-checked, uniformed, and working under the same values code our founder Victor Salinas has held to since he was welding next to his father: measure twice, weld once, and never cut corners on a hinge holding a thousand pounds.
FAQs
If your gate is still under a fabricator or installer warranty, the answer depends on who installed the opener and whether they followed Ghost Controls’ installation specs. As an independent Ghost Controls service provider, we install to factory specifications, which keeps most warranties intact. Read your gate warranty, ask us before we start, and we’ll tell you in plain English what’s covered.
Yes, in most cases. A limit reset, a remote re-learn, or a board diagnosis takes one visit. If we need a specific part that isn’t in our van stock, we order it and tell you when it arrives. Call (817) 286-7391 and we’ll give you a realistic arrival window, not a vague “sometime next week.”
If your opener is under ten years old and the gate itself moves freely, repair is usually the right call. If the board is dead, the motor is smoked, and the gate was installed in the Bush administration, replacement starts making more sense. We’ll show you the numbers both ways and let you decide. We don’t push replacement unless the math is clear. If the gate’s not working right, it’s not done.
Yes. We fabricate gates, set posts, hang leaves, and install the Ghost Controls opener as one integrated job. Most gate companies only hang the opener. We build the whole assembly, so the weight, swing, and balance are all matched to what a Ghost Controls opener is rated to pull.
A single swing gate opener install takes half a day. A double gate or a full gate-and-opener job is usually one full day. We tell you the window before we book, and we’re there when we say we’ll be.
Get a Free Estimate for Ghost Controls Gate Installation in Kennedale
If your Ghost Controls gate isn’t opening right, call (817) 286-7391. A live person answers. We’ll talk through what’s happening, give you a straight answer on whether to repair or replace, and quote a firm price before any work starts. Serving Kennedale and the surrounding Tarrant County area for over 42 years. Done right, and backed in writing.
Written by Victor Salinas, Owner & Gate Repair Specialist, Ironworks Gate Co. at Ironworks Gate Co., serving Kennedale and nearby areas.