Linear Gate Repair Nationwide

Linear Gate Repair in Kennedale: What to Know First

Linear gate repair in Kennedale is work we take on every week, and most Linear opener problems can be repaired in one visit. For a failing Linear actuator arm or a control board that’s lost its mind, you’re usually looking at between $225 and $520 for parts and labor, depending on what the diagnosis turns up. We’re an independent Linear service provider, not a Linear dealer, which means we have no interest in selling you a new operator when a $40 limit switch or a rebuilt gear set will do the job. Call us at (817) 286-7391 and a live person will answer, day or night. This page is for Kennedale homeowners whose Linear gate opener has stopped doing its job: if the arm stopped moving, the remote quit working, or the gate makes a grinding noise it never made before, you’re in the right place.

Call (817) 286-7391

How Linear Products Fail - and How We Fix Them

We have been inside enough Linear operators to know that each model line has its own habits. Here are the failures we see most often on Kennedale driveways:

• Linear Louver Series (LRA/LA series): the actuator arm goes soft. The Linear LRA actuator arm is a workhorse on Kennedale swing gates, but after years of Texas heat cycles, the internal gears wear down until the arm pushes weakly or makes a ratcheting noise while the gate barely moves. We rebuild the gear pack with OEM Linear parts or, where the housing is still sound, we replace the arm entirely with a new Linear unit. No point patching a gear set that’s already on its way out.
• Linear SL (Slide series): limit switches fall out of adjustment. Linear slide operators, common on Kennedale’s wider lots off Sublett Road and along Kennedale Parkway, rely on mechanical limit cams that drift over time. The gate stops short, opens too far, or reverses mid-travel. The fix is a limit adjustment plus a tension check on the drive chain. Fifteen minutes of work that prevents a slide gate from yanking itself off the rail.
• Linear PRO-Series (intercom-capable systems): cold solder joints on the relay board. It’s a quiet failure: the gate works on the keypad but not the intercom, or vice versa. We trace it to a cracked solder joint on the relay board, not a programming issue. We resolder the joint or replace the board, and we test every input before we back out of the driveway.
• Linear gate arms after a power surge: the transformer takes the hit. North Texas storms bring lightning, and when a surge comes down the lines, the Linear transformer on the 24V side is often the first casualty. We check the transformer, the capacitor, and the control board in that order. On older Linear units, replacing the transformer and capacitor together is cheaper than a new board and gets the gate running for another five years.
• Access control units (Linear AK-11 and AK-21): the keypad face wears, not the electronics. On Kennedale gates with a Linear keypad, the most common issue is a faceplate so sunworn the buttons are unreadable, or a membrane that lets water in. The electronics inside are usually fine. We replace the faceplate or membrane with a new Linear part, reseal the edge, and the keypad keeps working for years. It’s the cheapest repair we do on Linear gear, and one of the most common.

The pattern across all of it: Linear equipment is built well but it’s not immune to Texas heat, lightning, and plain years of use. Parts are available for most series still in service. We know which ones are worth repairing and which ones have crossed the point where replacement costs less than repair. We’ll tell you straight either way.

Our Linear Gate Repair Process

This is how a Linear repair job runs when we come to your Kennedale home:

1. 1
   You call (817) 286-7391. A live person answers, asks what the gate is doing (or not doing), and schedules a visit. No phone tree, no callback wait.
2. 2
   We come out and listen. We run the gate, hear the motor, watch the arm or rail, and check the control board. We don’t start swapping parts until we know what failed.
3. 3
   We tell you the diagnosis and the cost. You get an exact number before a single bolt is turned. If you’d rather not spend the money that day, that’s fine; the diagnosis is yours to keep.
4. 4
   We make the repair. We use OEM Linear components where they’re the right call, and tell you when a quality aftermarket part does the same job for less. No guessing on a board that’s holding your gate’s logic together.
5. 5
   We test it hard. We run several full cycles, listen for strain, check the limits, and make sure the remote, keypad, and safety edges all respond the way they should.
6. 6
   We clean up and stand behind it. The work area is cleaner than we found it, and every job carries the 90-Day Done Right Promise in writing. If it’s not right, we come back. No argument.

What Linear Gate Repair Costs in Kennedale

Linear gate repair costs in Kennedale run between $180 on the low end for a simple limit switch adjustment or keypad faceplate replacement, and $620 for a full actuator arm swap on a swing gate. Most jobs fall between $225 and $400. Here’s a straight read on typical pricing:

• Limit switch adjustment on a Linear slide opener: $180 to $260
• Keypad faceplate or membrane replacement (AK-11/AK-21): $160 to $240
• Control board replacement (relay board, PRO-Series): $340 to $520
• Transformer and capacitor replacement after a surge: $220 to $300
• Full actuator arm replacement on a Linear swing gate: $420 to $620

What moves the price is parts. A Linear board costs what it costs; a faceplate doesn’t. We price the job up front, agree on the number with you before we start, and the bill matches the quote, every time. Senior and veteran customers take 5% off every job, always. Call (817) 286-7391 for a free estimate on your Linear repair.

Why Kennedale Homeowners Call Ironworks Gate Co. for Linear Work

We were founded in 1984, and we have spent the years since earning a simple reputation: the company that shows up when it says it will and fixes the gate so it stays fixed. Every job carries the 90-Day Done Right Promise in writing, which means if it is not right, we come back and make it right. No paperwork, no arguing. Victor Salinas grew up in Kennedale, not far from the old Kennedale Stockyards grounds, and he runs the company with a welder’s respect for metal and a technician’s exactness for the motor. Linear is one of nine gate-automation brands our technicians are trained on: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. That matters when a Linear actuator shares a driveway with a Ghost Controls remote or an older DoorKing keypad. We know how they talk to each other, and we know how to keep them from fighting. If the gate’s not working right, it’s not done.

FAQs

Call Ironworks Gate Co. for Linear Gate Repair in Kennedale

If your Linear gate has stopped behaving, don’t guess at the problem. Call us at (817) 286-7391 and describe what you’re seeing. A live person will answer, we’ll give you an honest read on what it likely is, and we’ll schedule a visit that suits you. The estimate is free, the price is agreed before we start work, and every repair carries the 90-Day Done Right Promise in writing. We have been serving Kennedale and nearby areas for over 42 years. We plan to be here when you need us again.

Written by Victor Salinas, Owner & Gate Repair Specialist, Ironworks Gate Co. at Ironworks Gate Co., serving Kennedale and nearby areas.