Linear Keypad & Intercom Repair Nationwide

Linear Keypad & Intercom Repair: The Kennedale Owner’s Guide

Linear keypad and intercom repair in Kennedale typically runs $185-$420 installed, depending on whether we’re replacing the keypad face, the intercom board, or the entire unit. We carry Linear-compatible keypads, intercom modules, and wiring harnesses on our trucks, and most repairs are completed in a single visit. The way most Kennedale homeowners discover the failure is mundane: the keypad stops lighting up, the intercom goes silent mid-call, or the gate works from the remote but not from the pad by the driveway.

Call (817) 286-7391

It’s a specific failure, and it frustrates people because everything else on the gate still works. The motor runs. The remote clicks. But the keypad sits there dead, and suddenly the way you let a delivery driver in, or a grandkid who forgot their clicker, is gone. We’ve fixed hundreds of these across Tarrant County, and the fix is usually faster than the diagnosis.

Which Linear Models This Applies To

Most Kennedale gates with Linear keypads are running either the older blue-faced AK-11 series or the newer backlit models like the AP-5 and the MVS keypad line. The intercom side is usually a Linear AM-KP or an AE-series entry system tied into the gate operator. The compatibility gotcha few owners know about: Linear changed their wiring pinouts between the older 2000s-era boards and the current production, so a keypad that fits the box may not talk to the board without a small adapter or re-pin. That’s the kind of detail that turns a thirty-minute job into a two-hour headache if the tech doesn’t know it going in.

When we identify the part, we look at three things: the model label on the back of the keypad, the wire count at the terminal block inside the gate box, and whether the intercom is a two-wire or four-wire system. Linear made both, and they are not interchangeable. We stock genuine Linear parts alongside quality aftermarket equivalents that match the original specs, and for an independent service company we’re not affiliated with Linear, but we know their product line cold. We’re also set up for LiftMaster, Mighty Mule, and Ghost Controls parts on the same truck, which helps when a Kennedale home has mixed brands across two gates.

Signs Your Linear Keypad & Intercom Repair Is Failing

• Keypad lights up but won’t trigger the gate. This is usually a relay failure inside the keypad or a pinched wire between the keypad and the operator board. The keypad thinks it sent the signal, but the gate never hears it.
• Buttons need hard, repeated presses. The membrane contacts under the rubber face wear out, especially on units exposed to full afternoon sun. Once the carbon contact pads are worn, cleaning rarely brings them back for long.
• Intercom audio is crackling or one-way. This points to corrosion on the speaker connections or a failing capacitor on the audio board. Texas humidity and heat cycles accelerate this on units mounted without a weather hood.
• Gate opens from the remote but not from the keypad. The keypad’s power feed or data line is compromised while the receiver still works fine. This is the most common call we get in Kennedale, and it’s usually a repairable wiring fault rather than a full keypad replacement.
• Keypad works for a week, then stops until you reset the breaker. This signals a short drawing excess current, often from moisture ingress in the keypad housing or a failing voltage regulator on the board. Left alone, it can damage the gate operator’s main board.

Replacement Cost & What’s Included

A basic Linear keypad swap in Kennedale runs $185-$275 for a straightforward single-gang replacement with existing wiring. A full keypad and intercom replacement, including a new mounting box, weather hood, and rewiring, typically lands between $300-$420. The spread comes down to wire condition (old corroded wire takes longer to pull through conduit), access to the operator board, and whether we’re matching an older Linear pinout or the current one. Every job includes the part, the labor, wiring checks, and a function test of the entire gate cycle so the keypad, intercom, and motor all talk to each other correctly. The price is quoted and agreed before we turn a single bolt, and the work is covered by our 90-Day Done Right Promise, in writing.

DIY or Call Us?

This is where we earn our keep honestly. Low-voltage keypad work is not in the same danger category as high-tension gate springs or an exposed operator board, but it will bite you in a different way: a mis-wired keypad can short the main gate board, and that board costs several hundred dollars to replace. If you want to check the obvious before calling, we’d say confirm the breaker is on, check that the keypad face isn’t cracked or water-filled, and look for loose or corroded wire nuts in the keypad housing. Past that, the wiring inside the operator box is where mistakes get expensive. We answer the phone 24 hours a day, 7 days a week at (817) 286-7391, and a real person picks up.

FAQs