Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterMighty Mule Gate Access Control in Kennedale: What to Know First
Mighty Mule gate access control repair in Kennedale typically runs $160 to $380 for keypad, receiver, and wiring fixes, and many jobs are finished the same day. We are an independent Mighty Mule service provider, not a manufacturer-authorized dealer, which means we can tell you plainly when an OEM part matters and when a reliable aftermarket part does the same job for less. If your keypad quit at the worst possible time or a remote stopped opening the gate, call (817) 286-7391: a real person answers, and the estimate is free.
How Mighty Mule Products Fail - and How We Fix Them
- MM371W and MM371 Wireless Keypads losing programming after a power blink. These entry keypads hold their codes in a small internal memory that sometimes clears itself when the control board loses power, even for a half-second. In Kennedale, where spring thunderstorms roll through regularly, that means the keypad goes brain-dead without warning. We reflash the code set, verify it survives a hard power-cycle, and if it drops again, we replace the keypad rather than make you reprogram it monthly.
- Mighty Mule FM200 / FM502 receivers failing to see new transmitters. The receiver’s learn button on older FM-series boards gets flaky with age, so the board never enters pairing mode even though everything else looks fine. We test the button and the radio module separately, and when the board’s at fault, we source a correct replacement before touching the opener motor itself.
- Vehicle exit wands and probe sensors fighting the access controls. A surprising number of Kennedale driveways run a Mighty Mule gate with an aftermarket exit wand or a loop detector tied into the same control input, and the gate refuses to close because the two systems argue. We trace the trigger wiring and isolate the conflicting zone instead of blaming the opener, which is what the last guy did.
- MM562 solar panels and battery-only installs dropping voltage at night. Gates set up with Mighty Mule’s solar option often get a low-voltage condition after sundown in winter, and the access receiver loses power while the gate motor still has enough juice to creep. The symptom is random: sometimes the remote works, sometimes it doesn’t. We correct the charge controller setting and verify the battery bank actually holds a full cycle.
- Disconnected or corroded push-button and intercom wiring at the gate post. Kennedale’s clay soil holds moisture, and gate-post conduit connections corrode faster than folks expect. When a Mighty Mule keypad or card reader stops working entirely, the cause is usually a corroded splice or a broken wire inside the post, not the accessory. We open the junction, clean or re-terminate every conductor, and seal it properly so it stays dry.
Our Mighty Mule Gate Access Control Process
- 1
The call. You reach a person, not a phone tree. We ask what the gate did, what the keypad or remote did, and whether the problem is from the house, the street, or both. That conversation alone saves half the wrong parts.
- 2
The visit. A uniformed technician shows up on time, with a meter and a known-good Mighty Mule transmitter on the truck. We test the receiver, the keypad, the limit switches, and the power supply before touching anything else.
- 3
The diagnosis, explained plainly. We tell you what failed and why, in words that make sense. You’ll know the exact fix and the exact price before we turn a single bolt.
- 4
The parts decision. Where an OEM Mighty Mule control board or receiver is the right call, we use it. Where a solid aftermarket part is functionally identical and saves you money, we say so. No guessing, no markup games.
- 5
The repair and the test. We install, wire, and then cycle the gate through keypad, remote, and any phone entry or intercom option at least 10 times from both directions.
- 6
The guarantee. Every job carries our 90-Day Done Right Promise in writing. If it is not right, we come back and make it right.
What Mighty Mule Gate Access Control Costs in Kennedale
Every quote is settled before the work starts, and the price we quote is the price you pay. Here are honest ranges for the Mighty Mule jobs we see most often in Kennedale:
- Keypad replacement or reprogramming: $120 to $240, depending on the model and wiring condition.
- Receiver board replacement (FM200 / FM502 era): $180 to $320 for parts and labor.
- Full access control upgrade with two remotes and a wireless keypad: $280 to $450.
- Video intercom or phone-entry add-on for a Mighty Mule opener: $500 to $1,100, plus power work if the feed from the house needs upgrading.
- Diagnostic service call (applied toward the repair): $89.
What moves the price: the age of the board, how much of the original wiring can be saved, and whether the gate’s power supply is still healthy. We also maintain standing offers: $50 off any repair over $250, a free second opinion on any written estimate, an $89 seasonal tune-up, and a 5% discount for seniors and veterans. Call (817) 286-7391 and we will tell you the number over the phone, free.
Why Kennedale Homeowners Call Ironworks Gate Co. for Mighty Mule Work
We have served this area for over 42 years, and the company was founded in 1984 with a simple rule: do the work right, write it down, and stand behind it. Every Mighty Mule access control job, whether it is a keypad replacement or a full video intercom, is covered by our 90-Day Done Right Promise. That is a written guarantee with no paperwork and no arguing. Our technicians are trained on nine gate-automation brands, including LiftMaster, Ghost Controls, and DoorKing, so when a Mighty Mule job turns out to have a mixed-brand setup, the correct fix happens on the first visit. Owner Victor Salinas grew up near the old Kennedale Stockyards grounds and started Ironworks Gate Co. after years of working on residential and commercial gate systems across Tarrant County, and he still treats every job like the gate belongs to his own mother. As Victor says, “If the gate’s not working right, it’s not done.”
FAQs
Yes. In most cases the keypad’s internal memory cleared when the control board lost power, and we can reprogram it on the spot. If it will not hold the codes, we replace it. Call (817) 286-7391 and we will get you on the schedule today.
We use whichever is correct for the job. When an OEM Mighty Mule receiver or control board is the only reliable option, we use it. When a quality aftermarket part performs identically and costs less, we tell you that plainly. We are an independent Mighty Mule service provider, so we are not pushed to protect a manufacturer’s parts pipeline.
In most cases we can have a technician out the same day or the next morning. A live person answers the phone 24 hours a day, 7 days a week, and most access control repairs are completed in one visit. Call (817) 286-7391 and we will give you a real arrival window.
If the gate motor and gearbox are healthy, repairing the access control is almost always the better value. Mighty Mule openers from the FM200 and FM500 era have durable drive sections, and most failures are in the receiver, keypad, or wiring, not the motor itself. We will tell you honestly if the mechanical side is worn past the point of good money.
Mighty Mule’s warranty covers the parts themselves; our access control repair does not void the opener warranty. We document what was replaced and why, and we honor manufacturer warranty-covered parts when the failure falls under their coverage. For the parts and labor we perform, our 90-Day Done Right Promise applies.
For Mighty Mule gate access control in Kennedale, call (817) 286-7391. We’ll give you a square price before any work starts, and we will stand behind it in writing.
Written by Victor Salinas, Owner & Gate Repair Specialist, Ironworks Gate Co. at Ironworks Gate Co., serving Kennedale and nearby areas.