Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Repair Across Fort Worth
Gate repair in Fort Worth usually costs between $185 and $690 depending on what failed, and most hinge, post, and opener issues can be diagnosed and fixed in one visit. We work the 76101, 76102, and 76103 corridors every week, and our crews know exactly what the Blackland Prairie clay does to a gate post that was set shallow forty years ago. Call (817) 286-7391 and a live person answers, day or night. Not a voicemail tree. Not a callback queue.
If your gate is leaning, dragging, stuck open, or the motor hums but nothing moves, you want someone who has seen that exact failure a hundred times before. We have. Fort Worth’s soil, heat, and freeze cycles punish gates in ways that surprise homeowners, but not us.
Why Ironworks Gate Co. Is Fort Worth’s Preferred Gate Repair Company
We have been repairing driveway and estate gates for over 42 years, founded in 1984, and we plan to be in Fort Worth for another forty. Homeowners here remember the last contractor who let them down. That is exactly why we put our 90-Day Done Right Promise in writing on every job. If it is not right, we come back and make it right. No arguing. No paperwork. No exceptions. It is called the Keystone Standard internally, and it applies to a hinge replacement the same as a full automation retrofit.
Our technicians are background-checked and uniformed, and they work in your driveway the way they would work in their own mother’s. Victor Salinas leads our crews, and the standard he sets is simple: the 400th job gets the same care as the first. When a Fort Worth homeowner calls us about a sagging gate on a 1960s ranch house, we are not guessing. We know the housing stock, we know the clay, and we know what those original installers did wrong. That local knowledge is why our Gate Repair team completes most jobs in a single visit, with upfront pricing settled before a single bolt is turned.
Our Gate Repair Services in Fort Worth
We work on the full scope of gate problems, from a rusted hinge to a dead control board. These are the four calls we run most often in Fort Worth.
Electric Gate Repair
When an electric gate stops responding, the problem is rarely the motor. More often it is the control board, a failed photocell, a bad limit switch, or a capacitor that gave out after one too many 105° days. We are trained and equipped on nine automation brands including LiftMaster, FAAC, and BFT, so we carry the right diagnostic tools and the right replacement parts on the truck. Most electric gate failures in Fort Worth are fixed on the first visit.
Automatic Gate Repair
Automatic gate openers in Fort Worth take abuse from both ends of the thermometer. Summer heat degrades rubber seals and plastic gears. Hard freezes crack hydraulic housings and seize gearboxes. If your opener struggles after a cold snap or labors through the afternoon heat, we can tell you honestly whether it is a repair or a replacement. And when replacement is the cheaper long-term answer, we will say so plainly instead of patching it for another season.
Hinge & Post Repair
This is the most Fort Worth-specific repair we do. Blackland Prairie clay expands when wet and contracts hard in drought, and any post set shallower than 36 to 42 inches will lean within one or two seasons. On older east-side properties in 76101 through 76103, many original gate posts were set shallow and without proper concrete piers. We dig them out, set new footings at the correct depth, and weld or bolt fresh steel posts that will stay true.
Gate Realignment
A gate that drags on the driveway or no longer latches cleanly has usually shifted at the post. Fort Worth’s clay heave after spring rains is the most common culprit, and it throws latch alignment off just enough to be annoying, or enough to leave the gate insecure. We correct the post, reset the hinges, and bring the gate back to square so the latch line stays true through the next wet-dry cycle.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Fort Worth
We service nine major gate-automation brands, including LiftMaster, FAAC, BFT, and Linear. That breadth matters when you have a 15-year-old opener on a pipe-rail gate and the original installer has long since gone. We stock common replacement parts for the brands most often found on Fort Worth driveways, so a repair does not stall waiting on a shipment from out of state. Whether it is a vintage operator still doing its job or a newer unit with a failed accessory, we diagnose correctly the first time.
Common Gate Repair Problems We See in Fort Worth Homes
- Post lean after spring rains. Expansive clay swells, pushes against the shallow footing, and the post leans. On pipe-rail and heavy ornamental iron gates common near the Stockyards heritage neighborhoods, the added weight makes the problem worse than on lighter suburban gates.
- Summer heat seizing hinges. Sustained 100°F+ stretches warp wooden gate frames and bind metal hinges, especially on older estate gates in the 76101-76103 corridor. The gate starts to stick, then the opener strain increases, and soon the motor or gearbox fails from overwork.
- Freeze damage to opener internals. Winter Storm Uri in February 2021 cracked hydraulic actuator housings and froze gearboxes solid across Fort Worth. Any opener that survived that freeze is now six years older and more vulnerable to the next hard snap.
- Rust and rot at grade. Original wood-and-metal gates on postwar concrete driveways often rot where the post meets the soil. The gate looks fine until it does not, and by then the post has pulled free of the clay and the latch no longer meets the striker.
Pricing for Gate Repair in Fort Worth, TX
We quote a fixed price before any work starts. Here is what Fort Worth homeowners typically pay, based on the jobs we run across the 76101, 76102, and 76103 zip codes.
- Hinge replacement or repair: $185-$420 depending on post condition and gate weight.
- Post reset with new concrete footing (36-42 inch depth): $390-$690 including welding and cleanup.
- Gate realignment and latch adjustment: $140-$310 on most residential gates.
- Electric gate diagnostic and repair: $190-$480 depending on the failed component.
- Opener replacement or retrofit: $650-$1,400 installed, brand-dependent.
The final number depends on what we find, but it never comes as a surprise. You get the price upfront, you approve it, and only then do we turn a single bolt. We also honor standing offers in Fort Worth: $50 Off Any Repair Over $250, a Free Second Opinion on Any Written Estimate, an $89 Seasonal Tune-Up, and a permanent 5% Senior and Veteran discount. Call (817) 286-7391 for an exact quote. Estimates are free.
Why Fort Worth’s Soil and Weather Attack Gates Differently
Fort Worth sits squarely on the Blackland Prairie, and the clay underneath this city is the defining factor in how gates fail here. It is not a subtle effect. When the clay is wet, it swells with enough force to push a shallow post sideways. When summer drought bakes it, the clay contracts and pulls away from the concrete, leaving the post loose in the ground. Repeat that cycle for a few years and any post set less than 36 to 42 inches deep will be visibly out of plumb. Contractors from outside North Texas routinely underestimate this, set posts at 24 or 30 inches like they would in sandier soil, and are gone by the time the gate starts dragging. We are not gone. We are thirty minutes away, and we factor proper post depth into nearly every repair quote on properties near the older Near Southside and Polytechnic Heights neighborhoods.
On top of the clay, Fort Worth’s deep ranch-and-cattle identity anchored by the Stockyards heritage means pipe-rail and heavy ornamental iron driveway gates are common even on standard residential lots. Heavier gates on shifting soil means more leverage against the post, more stress on the hinges, and more frequent realignment than in comparable suburban cities to the east. That is not a guess. It is what we see every season.
Add in the climate: sustained 100°F+ summers that warp wooden gate frames and degrade rubber seals, followed by hard freezes that crack hydraulic actuator housings and seize gearboxes solid. The hot-then-frozen cycle here is more extreme than in Dallas or Houston. The result is a distinct pattern of repair calls that spikes in July and again after every ice storm. We plan our Fort Worth stocking around those two seasons.
An Older Gate Does Not Always Mean a New Gate
We get a lot of calls from Fort Worth homeowners with gates that were hung before modern safety requirements existed. Obsolete control boards that are no longer manufactured. Worn hinge pins on ornamental iron gates that have been swinging for sixty years. Posts that were set at 24 inches by the original builder and have been leaning since the Clinton administration. The question is always the same: fix it or replace it. Our answer is honest, case by case. A well-built vintage iron gate can almost always be salvaged, rehung, and made safe with current hardware. A rotted wooden gate with a seized post and a dead operator may be cheaper to replace than to patch. We will walk you through the math before you spend a dollar.
One job sticks with us. We reset a sagging pipe-rail swing gate on a 1950s ranch house in Polytechnic Heights, where the original hinge post had rotted at grade and pulled free of the clay. Our crew dug a new 42-inch post footing, welded a fresh steel hinge post, and rehung the gate with sag correction so the latch line stayed true. Before leaving, we tested the existing LiftMaster operator’s safety photocells and found them dead. We replaced them the same trip so the gate would not crush a pet or child. That is the difference between a handyman patch and a gate specialist who knows what to look for.
Safety on High-Tension Gate Hardware
Automatic gates carry genuine risk. Springs, cables, and pinch points can injure a person if a gate fails or if a safety device is bypassed. We strongly recommend that any repair involving gate springs, opener motors, or safety sensors be handled by a trained professional with the right tools and the right respect for the equipment. We do not give step-by-step DIY instructions for high-tension components, because the worst-case scenario is not a broken gate. It is a trip to the emergency room. If your gate is binding, sparking, or moving erratically, call us instead of experimenting with the springs.
We Also Serve Cities Near Fort Worth
Beyond Fort Worth proper, we run daily routes through Haltom City, Hurst, Kennedale, and Bedford for gate repair and opener work. If you are in any of those communities, the same Fort Worth team handles your call and dispatch from the Dallas-Fort Worth metro office. Same pricing. Same warranty. Same live person on the phone.
Serving Fort Worth, TX - Our Local Coverage Area
We’re based in the Fort Worth area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Repair in Fort Worth
Your post is likely set too shallow for Blackland Prairie clay. When the clay gets wet, it swells with enough force to push a shallow footing out of line. When it dries, the post settles into the gap and stays crooked. Any post set less than 36 to 42 inches deep in Fort Worth will repeat this cycle until it is properly excavated and re-set with a deeper concrete pier. Call (817) 286-7391 and we will confirm the depth and give you a fixed price to do it right.
Usually not. The motor is often the last component to fail. What we typically find is degraded rubber seals, worn plastic drive gears, or a capacitor that has lost its punch after years of Fort Worth heat. The opener works, but it cannot push the gate as hard as it used to. We diagnose the specific weak point, and if the operator is too far gone, we will tell you honestly whether rebuilding it makes sense. Estimates are free.
Every automatic gate installed today must have photoelectric sensors or an equivalent entrapment-protection device. Your gate predates those requirements, and no one is going to fine you for owning it. But if we work on that opener, we will bring the gate up to current safety standards as part of the repair. A photocell pair costs relatively little, and it prevents a serious injury. We will not leave a gate operating without it.
At minimum 36 inches, and we prefer 42 inches with a proper concrete pier and gravel base for drainage. Fort Worth’s clay heaves and contracts too aggressively for anything shallower. If your gate has already sagged, the post may be fine and the hinge pins may be worn, or the post may be moving and the hinges are along for the ride. We will tell you which one it is before we quote the repair.
In almost every case we can salvage it. Vintage ornamental iron from the early and mid-20th century is usually better material than what is sold new today, once the rust is cut away and the hinges are rebuilt. We remove the gate, cut out the seized hinge post, set a new steel post at 42 inches, repair or replace the hinge straps, and rehang the gate with its original character intact. The only time replacement makes sense is when the iron itself has lost structural integrity. Call (817) 286-7391 and we will give you a straight answer and a written quote.
Call Ironworks Gate Co. for Gate Repair in Fort Worth
If your gate is leaning, sticking, silent, or just not closing the way it used to, call (817) 286-7391. A live person answers 24 hours a day, 7 days a week. We will schedule a visit, diagnose the problem, and give you a fixed price before any work begins. Every job is backed by our written 90-Day Done Right Promise. No surprise invoices. No chasing a contractor who disappeared. Done right, and backed in writing. That is how we work in Fort Worth.
Written by Victor Salinas, Owner at Ironworks Gate Co., serving Fort Worth and the surrounding North Texas communities.