Gate Parts & Welding in Bedford - Made to Measure, Written Price

Gate Parts & Welding in Bedford, TX: What It Costs and How We Fix It Right

Gate parts and welding repair in Bedford typically runs $180 to $1,400 depending on whether we’re resetting a heaved hinge post, replacing a cracked weld, or rebuilding an entire 1970s ornamental iron gate. Most jobs on Bedford’s original ranch homes are completed in a single visit because the failure is almost always the same: expansive clay soil has pushed posts out of plumb, and the hardware followed. Call (817) 286-7391 and you’ll get a live person, a straight answer, and a written price before any work begins.

Call (817) 286-7391

Bedford’s housing stock was built almost entirely between the late 1960s and early 1990s. That means the original wooden and ornamental iron driveway gates hung on those homes are now 30 to 55 years old, and they’re failing together. We work these neighborhoods every week, from the ranch homes off Harwood Road to the brick-clad streets of the 76022 zip code. If your gate drags at the latch, sags at the hinge, or won’t close square anymore, the post underneath it has probably moved. We fix the post first, then the gate.

Why Ironworks Gate Co. Is Bedford’s Preferred Gate Parts & Welding Company

We’ve been doing this work for over 42 years, founded in 1984, and Bedford homeowners call us because we understand what’s happening under their gates. The black-clay soil in this part of Tarrant County swells and shrinks with every wet-dry season cycle. A hinge post set 40 years ago with no concrete footing doesn’t stand a chance. We see it on Daniel Drive, along Cheek-Sparger Road, and in the quiet cul-de-sacs off Forest Ridge. The gate panel looks fine. The post underneath has risen three inches and taken the latch with it.

Every Bedford job is protected by our written 90-Day Done Right Promise. No paperwork, no arguing. If it’s not right, we come back and make it right, on every job, no exceptions. That’s the Keystone Standard, and our Gate Parts & Welding team applies it to hinge replacements, post resets, custom welding, and everything else we touch. Victor Salinas leads our crews with a simple rule: the 400th job gets the same care as the first. Bedford homeowners between 55 and 75, who have lived in their homes for twenty years or more and plan to stay, understand exactly what that means.

When you call (817) 286-7391, a live person answers. Not a voicemail, not an answering service. 24 hours a day, 7 days a week. Dispatch and scheduling are coordinated from our Dallas-Fort Worth office, and our uniformed, background-checked technicians serve Bedford locally. We’ll be there when we say.

Our Gate Parts & Welding Services in Bedford

Hinge Replacement

Bedford’s original 1970s and 1980s swing gates were hung on hinge hardware that has now survived four decades of Texas heat, ice storms, and clay movement. We carry heavy-gauge replacement hinges sized for both wooden privacy gates and ornamental iron driveway gates, and we set them on posts that are plumb and solid first. A hinge replacement in Bedford runs $180 to $420, and most are finished the same day.

Post Replacement

This is the number-one call we get in Bedford. Original wooden posts across the 76021 and 76022 zip codes were set with minimal or no concrete, and the black clay has heaved them inches out of line. We pull the old post, dig a proper footing below the clay’s movement zone, pour concrete, and reset a steel or new timber post. Post replacement in Bedford typically runs $350 to $900 depending on footing depth and whether we’re also correcting gate alignment. Done right, it should outlast the original by decades.

Rail Repair

On wooden swing gates, the top and bottom rails take the entire load. When a hinge post heaves, the rail twists and splits. We sister rotted or cracked rails with pressure-treated lumber or steel, then re-square the entire gate before remounting. Most Bedford rail repairs run $220 to $500 and are completed in a single visit.

Custom Welding

Factory welds on ornamental iron gates crack under DFW ice storm stress, especially the February 2021 freeze that hit Bedford hard. We weld in place when possible, or remove the gate and weld on a jig in our shop when the frame is too far out of square. We also build custom steel braces, patch rails, and reinforce sagging frames. Custom welding in Bedford runs $195 to $1,400 depending on the scope. We’ll quote it in writing before we strike an arc.

Trusted Brands We Service in Bedford

Our Bedford customers run gates from every decade, and we’re trained and equipped on the automation that goes with them. We service LiftMaster, Mighty Mule, FAAC, and BFT openers, along with five other major brands, so whatever is on your driveway, we can fix it right the first visit. Since we work exclusively on gates, we keep common Bedford parts and steel stock on our trucks. That means less waiting and more getting the gate closing like the day it was hung.

Common Gate Parts & Welding Problems We See in Bedford Homes

• Clay-soil heave lifting hinge posts: Bedford’s black clay swells in wet months and contracts in drought, slowly jacking 1970s-era posts out of the ground. The gate panel looks fine, but the latch won’t line up and the gate drags. We reset the post with a proper footing before touching any hardware.
• Weld cracks from ice storms: The 2021 freeze and repeat seasonal temperature swings crack factory welds on ornamental iron frames. In the 76095 neighborhoods off Murphy Drive, we routinely reweld split joints and add steel reinforcement so the frame holds square.
• Tight side-yard clearance scraping: Bedford’s ranch homes sit on 6,000 to 8,500 square foot lots, and swing gates often operate inches from brick walls or fencing. When a post shifts even slightly, the gate scrapes. We correct the post, not just the scrape.
• Original wooden posts with no footing: Homes built in the 1970s and early 1980s across Bedford often have gate posts set directly in dirt. After forty years of clay movement, those posts are done. We replace them with steel posts or properly footed timber.

Pricing for Gate Parts & Welding in Bedford, TX

We Also Serve Cities Near Bedford

Our crews serve Bedford and the surrounding Mid-Cities communities, including Hurst, Haltom City, Fort Worth, and Grand Prairie. If you’re in a neighboring town and need gate parts or welding work done right, call (817) 286-7391 and we’ll get you scheduled.

FAQs - Gate Parts & Welding in Bedford