Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Installation Across Fort Worth
A complete driveway gate installation in Fort Worth typically runs between $2,800 and $7,500, and most jobs are finished in one day once materials are on hand. We’re Ironworks Gate Co., and we’ve been setting posts, hanging steel, and wiring operators in Fort Worth long enough to know that the clay under your driveway cares more about footing depth than any spec sheet does. That’s the difference between a gate that still swings true in five years and one that binds shut after the first wet spring. Call (817) 286-7391 and we’ll schedule a free measure at your Fort Worth home.
We work in the 76101, 76102, and 76103 zip codes weekly, from downtown Fort Worth east through Polytechnic Heights and the older neighborhoods off Rosedale Street and East Lancaster Avenue. Dispatch runs out of our Dallas-Fort Worth office, and our Fort Worth crews know the short blocks, the shared driveways, and the tight setbacks that make gate work here different from anywhere else in the metro.
Why Ironworks Gate Co. Is Fort Worth’s Preferred Gate Installation Company
Homeowners across Fort Worth call us because we do one thing: driveway and estate gates. Not fences with a gate as an afterthought. Not general contracting. Gates. We’ve been at it for over 42 years, and in that time we’ve replaced enough leaning posts and seized operators in Fort Worth to know exactly what fails here and why. Victor Salinas leads our crews, and the same background-checked, uniformed technicians who show up at your door are the ones who weld the hinges and wire the motor.
Every gate job in Fort Worth gets our 90-Day Done Right Promise in writing. If something isn’t right, we come back and make it right. No arguing, no paperwork. That’s the Keystone Standard we’ve applied to every job since 1984, and it applies to your gate in Fort Worth the same as it did to our first job four decades ago. A live person answers our phone 24 hours a day, seven days a week, so when your gate won’t open at 6 a.m. on a Tuesday, you get a person, not a voicemail.
Our standing offers for Fort Worth customers: $50 off any repair over $250, a free second opinion on any written estimate, an $89 seasonal tune-up, and a permanent 5% senior and veteran discount. You’ll know your price before a single bolt turns. A square deal, written down, agreed to in advance.
Our Gate Installation Services in Fort Worth
Fort Worth’s housing stock runs from mid-century brick ranches to early bungalows, and the right gate type depends on your lot, your driveway, and your neighbor’s property line. Here’s what we install most often in Fort Worth.
Sliding Gate Installation
In the 76103 zip code and older east-side neighborhoods, shared driveways and rights-of-way often leave no room for a swing gate’s arc. A sliding gate rides parallel to the fence line on a track or cantilever system, so it never crosses into a neighbor’s access. In Fort Worth, where many homes sit on short blocks with narrow side setbacks, sliding gates are often the only option that won’t block a shared drive. See our full Gate Installation scope for details on cantilever versus track systems.
Driveway Gate Installation
Fort Worth’s ranch-and-cattle heritage means pipe-rail and ornamental iron driveway gates are common even on standard lots. Those gates are heavy, and heavy gates on Blackland Prairie clay demand deeper posts than lighter suburban gates. We set posts at 42 inches or deeper as standard practice in Fort Worth, because anything less and the clay will make its opinion known within a season or two.
Pedestrian Gate Installation
A pedestrian gate seems simple until it isn’t. On Fort Worth’s older bungalow lots, the pedestrian gate usually hangs between a house corner and a fence return, often on ground that slopes toward the alley. We build pedestrian gates with welded steel frames and adjustable hinges, and we set the posts to the same depth standard as our driveway gates. A sagging pedestrian gate in Fort Worth is almost always a post-depth problem, not a hinge problem.
Swing Gate Installation
Double swing gates work well on Fort Worth properties with wide frontages, where both leaves have room to arc without hitting a parked car or a fence. We install single and double swing gates throughout Fort Worth, including the double-pipe-rail look common off East Rosedale and in the Near Southside. On double gates we use a center drop rod and cane bolt, and we set the hinge posts with the same deep-footing standard, because a double gate exerts double the leverage on the clay.
Security Gate Installation
Fort Worth homeowners who want real access control get a welded steel security gate with a coded keypad, a loop detector for exiting vehicles, and safety photocells at the drive line. We install LiftMaster, FAAC, and Mighty Mule operators on Fort Worth security gates, and we run the low-voltage power and safety edge wiring so the system works the day we leave. Every security gate we install in Fort Worth gets a walk-test of the photocells and a loop sensitivity check before we call it done.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Fort Worth
Our Fort Worth crews are trained and equipped on nine gate-automation brands, and we stock the common parts for LiftMaster, FAAC, BFT, and Mighty Mule right on our trucks. That means when your Fort Worth gate motor fails, we usually have the board, the gear, or the capacitor on hand, not on order. Most Fort Worth repair and installation jobs finish in a single visit. If your gate came with a LiftMaster operator and you want to keep it, we’ll keep it and make it work right. If it’s a Mighty Mule from a box store that never worked correctly, we’ll tell you straight what it needs and what it would cost to replace it with something built for Fort Worth’s heat and freeze cycles.
Common Gate Installation Problems We See in Fort Worth Homes
- Posts leaning in expansive clay: Fort Worth’s Blackland Prairie clay swells when wet and shrinks when dry, and a post set at the 24-inch minimum common elsewhere will visibly lean within one or two wet-dry seasons. We auger footings 42 to 48 inches deep and set posts in concrete that extends below the active clay zone, so the gate doesn’t bind against the drive or the latch stop.
- Shared driveways that can’t fit a swing gate: Older east-side Fort Worth neighborhoods often have driveways shared between two houses, with the property line running straight down the middle. A swing gate would arc across the neighbor’s half of the drive. A slide gate, or a swing gate rebuilt to hinge from the correct post, is the way to keep both neighbors able to park.
- Summer heat warping wooden gate frames: Fort Worth’s 100-degree-plus summers dry out wooden gate frames and seize metal hinges, and the heat can degrade rubber seals on operators. We see it every July. A steel frame with proper clearance and a heat-rated operator seals is the standard for a gate that survives a Fort Worth summer.
- Freeze damage to operator gearboxes: Winter Storm Uri in February 2021 cracked hydraulic housings and froze gearboxes all over Fort Worth. We replaced dozens of operator internals that spring. If your new gate will live through a Fort Worth freeze, the operator needs a freeze-rated gearbox and a heater option, not just a rain cover.
Pricing for Gate Installation in Fort Worth, TX
Here are straight numbers for Fort Worth. A single driveway swing gate with steel posts and basic hardware runs $2,800 to $4,200. A double swing gate in pipe-rail or ornamental iron runs $4,500 to $7,500. A sliding driveway gate, which requires a track or cantilever system and often a concrete pad, runs $4,800 to $8,500. A pedestrian gate installed on new posts runs $900 to $1,800. A security gate with a LiftMaster or FAAC operator, keypad, photocells, and a loop detector runs $5,500 to $9,000. These are installed prices with the posts set to our 42-inch-plus Fort Worth standard. The price we quote is the price you pay, agreed in writing before work starts. Call (817) 286-7391 for a free measure at your Fort Worth property and a written number the same day.
We Also Serve Cities Near Fort Worth
Our crews cover Fort Worth and the surrounding North Texas communities, including Haltom City, Hurst, Kennedale, and Bedford. If you’re in one of those cities and need a gate set right in the same clay we deal with in Fort Worth, call the same number and we’ll send a local crew. See our Gate Installation in Fort Worth coverage details for zip codes and scheduling.
Key Takeaways for Fort Worth Homeowners
- Gate posts in Fort Worth need footings 42 inches or deeper to survive the Blackland Prairie clay. Anything less will lean.
- Sliding gates are the right answer for many shared driveways in the 76101-76103 corridor, where a swing gate’s arc would cross a neighbor’s property.
- Fort Worth’s heat-then-freeze cycle demands steel frames, deep posts, and freeze-rated operator internals. Wood frames and shallow footings fail here on a predictable schedule.
- We quote a written price before work starts. It doesn’t change. That’s the deal.
- Every job backed by the 90-Day Done Right Promise, in writing, for over 42 years.
How Fort Worth’s Clay Changes Gate Installation
Fort Worth sits on the Blackland Prairie, and the clay here is the most demanding soil our crews work in across the entire Dallas-Fort Worth metro. It swells when it rains and contracts in summer droughts, and the cycle repeats every single year. That movement doesn’t just nudge posts; it heaves them, cracks their concrete footings, and pulls shallow-set posts right out of the ground. We’ve watched a gate in the 76103 zip code lean six inches in a single rainy spring. The local standard we’ve learned over decades, not read from a spec book, is that any post set less than 36 to 42 inches deep in Fort Worth’s black clay will visibly lean within one or two wet-dry seasons. So every gate installation we do in Fort Worth begins with footings augered 42 to 48 inches deep, through the active clay zone and into stable soil below. West of town, where limestone sits near the surface, a 24-inch footing might hold. Here, it won’t.
This matters more in Fort Worth than in the suburbs to the east because of the housing stock. The 76101 to 76103 corridor covers downtown and the older east-side neighborhoods where mid-century brick ranches and early-20th-century bungalows still stand. Many of those homes have original wood-and-metal gates on postwar concrete driveways, and the original posts were set shallow and without proper piers. Those posts have been fighting the clay for fifty years or more, and most of them are losing. When we come out to measure for a new gate in Fort Worth, the first thing we check is not the gate. It’s the ground under it.
A Polytechnic Heights Gate, Replaced in One Afternoon
In Polytechnic Heights, our crew replaced a sagging chain-link drive gate that had pulled its hinge post eight inches out of grade, leaving the driveway half-blocked. The owner had been propping the gate open with a cinder block for months. We augered 48-inch footings through the clay, set new 4-inch schedule-40 steel posts in concrete that reached below the active soil zone, and hung a custom pipe-rail swing gate with a LiftMaster operator and safety photocells. The homeowners were back to parking inside the same afternoon. We added a loop detector so the gate opens automatically for exiting vehicles, because nobody in Fort Worth wants to roll down a window and punch a keypad every time they leave for work. Victor Salinas walked that job personally, the same way we walk every Fort Worth install, before we called it finished.
That job is not an outlier. In the Poly area and the Near Southside, shallow post footings are the rule on older gates, not the exception. The clay has been working on those posts for decades. By the time a homeowner calls us, the gate is usually binding against the drive, the latch stop is out of line, or the hinges are twisted. The fix is rarely a new hinge. It’s a new post, set deeper, with the gate rehung square on steel.
Shared Driveways and the Slide Gate Answer
Fort Worth’s east side has a problem that newer suburbs don’t: shared driveways and recorded rights-of-way that run down the middle of a lot line. In the 76103 zip code, you’ll find driveways that serve two houses, with a fence line running parallel and the property boundary splitting the concrete. A swing gate on a shared driveway is a fast way to start a fight with a neighbor, because one leaf of the gate arcs straight across the other owner’s access. The only correct answer in many of these Fort Worth lots is a slide gate that runs parallel to the fence and never crosses the property line.
We install sliding gates in Fort Worth with track systems on concrete pads or cantilever systems that roll clear of the drive without touching the ground. On a shared driveway off East Lancaster, a slide gate gives each homeowner their own access, keeps the gate off the neighbor’s side, and lets both cars exit without waiting. We’ve built sliding gates in tight Fort Worth side yards where a pickup truck couldn’t be parked for the install, and we did it with hand-carried steel and a portable welder. Tight lots are normal here. Our crews are used to it.
Security Gates in Fort Worth’s Older Neighborhoods
A security gate in Fort Worth is more than a steel barrier. It’s a system: the gate, the operator, the keypad, the loop detector, and the safety edges. On a house near Rosedale Street, where the driveway opens directly onto a busy residential cut-through, a security gate with a Mighty Mule or FAAC operator keeps solicitors out and lets the homeowner open the gate from inside without walking to the drive. We run the low-voltage power, set the photocells at the right height for a Fort Worth driveway’s slope, and program the keypad codes before we leave.
We also fix the security gates that other installers left half-working. A gate that closes on a car in the drive is a photocell that was never aimed correctly. A gate that opens by itself in the middle of the night is a loop detector that was never tuned. Fort Worth homeowners deserve a security gate that behaves the same way every single time. That’s what we build.
Serving Fort Worth, TX - Our Local Coverage Area
We’re based in the Fort Worth area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Installation in Fort Worth
Gate posts in Fort Worth need to be set 42 to 48 inches deep, through the expansive Blackland Prairie clay and into stable soil below the active shrink-swell zone. Anything less than 36 inches will visibly lean within one or two wet-dry seasons, and a 24-inch footing, common in limestone areas west of town, fails here on a predictable cycle. We auger every Fort Worth post hole to 42 inches minimum, and 48 inches for heavy steel gates. Call (817) 286-7391 for an exact recommendation on your lot, and a free measure.
A swing gate on a shared Fort Worth driveway typically won’t work, because one leaf of the gate arcs across the neighbor’s half of the drive and blocks their access. The correct answer for most 76103 shared driveways is a sliding gate that runs parallel to the fence line and never crosses the property line. We install both track and cantilever slide gates in Fort Worth’s east-side neighborhoods. Call (817) 286-7391 and we’ll tell you which one fits your driveway.
A box-store opener rated for a light wooden gate will usually fail on a heavy Fort Worth pipe-rail gate within a year, because the operator’s duty cycle and motor torque are not built for the gate’s weight or for Fort Worth’s heat exposure. We install LiftMaster, FAAC, and Mighty Mule operators sized to the actual gate weight and cycle count. For a free opinion on whether your existing opener can handle your gate, call (817) 286-7391. We’ll give you a straight answer and a written number for whatever you need.
In Fort Worth, a wet spring swells the Blackland Prairie clay and a summer drought contracts it, and the gate posts move with that cycle unless they’re set below the active soil zone. That’s why we set Fort Worth posts at 42 to 48 inches. A gate installed on shallow footings will bind, lean, and pull its latch stop out of line within a season or two, and a wooden frame will warp in the 100-degree heat. Steel frames, deep footings, and heat-rated operators are the Fort Worth standard. Call (817) 286-7391 to schedule a free measure before the next drought hits.
A loop detector is a wire loop buried in the driveway that senses the metal mass of your car and opens the gate automatically as you exit, without you touching the keypad. In Fort Worth, where many homeowners pull out of their drive multiple times a day, a loop detector keeps the gate from opening into a passing car on a residential cut-through and saves you from rolling down the window in a Fort Worth July. We install loop detectors on every security gate and most automatic driveway gates in Fort Worth. Call (817) 286-7391 and we’ll explain exactly how it works on your driveway.
Call Ironworks Gate Co. for Gate Installation in Fort Worth
If your Fort Worth gate is leaning, binding, or just worn out, or if you want a new gate built for the clay, the heat, and the freeze cycles this city throws at it, call (817) 286-7391. You’ll get a live person, a free measure, and a written price before any work starts. We’ve been setting gates in Fort Worth for over four decades, and we’ll be here to stand behind yours for the next four. Done right, and backed in writing.
Written by Victor Salinas, Owner at Ironworks Gate Co., serving Fort Worth since 1984.