Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Installation Across Haltom City
Gate installation in Haltom City usually means one of two things: replacing a chain-link swing gate that has spent fifty years fighting Tarrant County clay, or adding an automated driveway gate to a 1960s ranch where the original fence line has finally given out. We handle both every week. Our Gate Installation crews know the post-WWII housing stock east of Haltom Road, the Fossil Creek area, and every block in between. When you call (817) 286-7391, a live person answers and schedules a time we actually keep.
Why Ironworks Gate Co. Is Haltom City’s Preferred Gate Installation Company
We have been doing gate work in the Dallas-Fort Worth metro for over 42 years, founded in 1984, and a good portion of our calls come from Haltom City homeowners who are tired of patching the same sagging gate. Haltom City’s older neighborhoods throw specific problems at a gate installer: heaving posts, corroded hinge straps, and gates hung decades before modern safety standards existed. Our background-checked, uniformed technicians work under the K.E.Y.S. values code: Krafted right, Every time, Your home first, Standing behind it. The 400th job gets the same care as the first.
Every completed job carries the 90-Day Done Right Promise in writing. No paperwork, no arguing. If it is not right, we come back and make it right. That is the Keystone Standard, and it applies whether we are resetting a single hinge post on a pedestrian gate or automating a double driveway gate.
Dispatch and scheduling are coordinated from our Dallas-Fort Worth office, and crews serve Haltom City locally. A live person answers the phone 24 hours a day, 7 days a week. Not a voicemail, not an answering service.
Our Gate Installation Services in Haltom City
Swing Gate Installation
Most Haltom City homes have swing gates, because that is what the original 1950s and 1960s builders put in with the chain-link. A proper swing gate installation on this soil starts with the posts, not the gate panel. If the post has heaved out of plumb, no amount of hinge bending will save it. We dig out the old footing, set a new galvanized post in a deeper concrete collar, and only then hang and align the gate. On clay like Haltom City’s, that collar is the difference between a gate that stays square and one that drags again in two years.
Driveway Gate Installation
Driveway gates in Haltom City run the range from simple manual chain-link across a carport apron to automated steel frames with operators. The lot sizes east of Haltom Road are compact, so we often install single-leaf swing gates with an operator tucked tight to the hinge post. We size the operator to the gate’s weight, not the other way around. A 50-year-old chain-link frame with a fresh coat of paint can sometimes be retained and automated. Other times the rails are too racked and the panel has to go.
Pedestrian Gate Installation
A pedestrian gate on the side of a Haltom City ranch home is the gate people use every single day to get the trash out, let the dog in, or walk to the carport. That daily cycle is why the hinge side fails first. We install pedestrian gates with adjustable hinges and a diagonal brace so the frame cannot rack itself out of square, and we set the latch side with enough clearance in the footing that seasonal clay movement does not jam it shut every spring.
Sliding Gate Installation
Sliding gates are less common on Haltom City’s narrow lots, but when a driveway has no room for a swing arc, a cantilever or track slide is the answer. We build the base pad with local soil movement in mind, because a sliding gate on expansive clay needs a stable track bed. If the ground shifts under a track-mounted slide, the gate binds. We account for that before the first bolt goes in.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Haltom City
Our technicians are trained and equipped on nine gate-automation brands, including LiftMaster, FAAC, and Mighty Mule, so whatever is already on your driveway, we can usually work with it. For older Haltom City homes with operators installed in the 1990s or early 2000s, we often replace a dead control board rather than the whole motor, when the gearbox is still sound. If a full operator replacement is the cheaper long-term answer, we will tell you that plainly and quote it before any work starts.
Common Gate Installation Problems We See in Haltom City Homes
- Heaved hinge posts: The expansive black clay under Haltom City swells with spring rain and shrinks in summer drought. We routinely see 50-year-old chain-link hinge posts lifted two to four inches above grade, which twists the gate so the latch misses and the bottom rail drags a rut in the lawn. The fix is resetting the post in a concrete collar, not bending the hinge straps.
- Corroded hinge straps and hardware: Decades of Tarrant County soil contact and rain cycles eat through galvanized hardware. A strap that looks fine from the driveway can be paper-thin at the post and snap under modern wind load, dropping the gate onto the concrete.
- Freeze-damaged operators: Gate motors left in place through freeze-thaw events like Winter Storm Uri collect moisture that strips gears and shorts control boards. We see a lot of half-open gates in February around Haltom City.
- Gates hung before UL 325: Many older swing gates had no entrapment protection when installed. A modern gate operator installation in Haltom City includes safety photocells and proper obstruction sensing, which is both a code requirement and a real protection for kids and pets on these compact lots.
Pricing for Gate Installation in Haltom City, TX
A typical manual chain-link pedestrian gate installation in Haltom City runs $350 to $650, including new posts set in concrete collars. A single-leaf driveway swing gate, steel frame on new posts, runs $1,200 to $2,800 depending on width and whether we are reusing the existing fence line. Adding a gate operator with two remote controls and safety photocells typically adds $900 to $1,800, with brand and horsepower affecting that range. A sliding gate installation on a cantilever system starts around $2,500 and goes up with length and automation. Every price is quoted and agreed before any work starts, in writing. Call (817) 286-7391 for a free estimate on your specific gate.
We Also Serve Cities Near Haltom City
While this page focuses on Gate Installation in Haltom City, our crews regularly work the surrounding metro: Fort Worth, Hurst, Bedford, and Kennedale. If you live just outside the Haltom City line, the same team and the same 90-Day Done Right Promise apply. Visit our Haltom City service page for a full breakdown of what we do across the area.
Serving Haltom City, TX - Our Local Coverage Area
We’re based in the Haltom City area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Installation in Haltom City
Because the expansive black clay under Tarrant County swells when it gets wet, and it does not swell evenly. The hinge post lifts, the latch post stays put, and the gate frame torques. You will see the bottom rail drag on the hinge side and a gap open at the latch. The real fix is digging out the old post footing, setting a new galvanized post in a deeper concrete collar, and realigning the frame. Bending the hinge is a temporary patch that fails again the next wet season. Call (817) 286-7391 and we will look at the post, not just the panel.
Often yes, we can retrofit. If the chain-link frame is still square, the posts are solid in their footings, and the rails are not rotted through, we can mount a modern LiftMaster or FAAC operator onto the existing gate. We will want to check the hinges and the post depth first. If the frame has been racked by decades of clay movement, welding a new steel frame is sometimes cheaper than chasing a chain-link gate that has fought the soil for 60 years. We will show you the numbers and let you decide.
If the motor and gearbox are in good shape and the failure is moisture intrusion on the control board, replacing the board is usually the cheaper, faster fix, and we do it in one visit. But if the gears are stripped from trying to move a frozen or overloaded gate, or if the operator is more than about 15 years old and parts are no longer made, a new operator with a fresh installation is the more honest answer. We will open it up, show you what failed, and quote both options before we touch anything.
Yes. UL 325 entrapment protection has been the standard for gate operators for years, and any new installation we do includes photocells and obstruction sensing. It is a code requirement, but more importantly, these older Haltom City yards are compact, with kids and dogs moving through them every day. A gate that reverses when it hits something is not an upsell. It is the difference between a gate closing and a gate hurting someone.
For most Haltom City lots, a steel-framed swing gate with posts set in deep concrete collars is the most forgiving option, because the gate hangs from the posts and can be realigned if the soil moves. A sliding gate needs a stable track bed, and on expansive clay that means a reinforced concrete pad, which adds cost and excavation. If you are replacing a 50-year-old chain-link gate that has heaved and been patched for decades, a new steel frame with a modern operator is usually the setup you will not have to think about again for a long time. Call (817) 286-7391 for a free measure and a written quote.
Call Ironworks Gate Co. for Gate Installation in Haltom City
We rehung a swing gate on a 1960s ranch near Fossil Creek where the original hinge post had heaved three inches out of plumb, twisting the gate so badly the latch missed by two inches and the bottom rail dragged a rut in the lawn. Our crew dug out the old post footing, set a new galvanized post in a deeper concrete collar, realigned the frame, and installed a fresh LiftMaster gate operator with a safety photocell to bring it up to UL 325 entrapment protection. That is the kind of job we do on Haltom City blocks every month.
Whether you need a new pedestrian gate, a full driveway gate installation, or a straight answer about whether to reset, retrofit, or replace, call (817) 286-7391. The estimate is free, the price is written down before work begins, and a live person answers when you call. We will be there when we say.
Written by Victor Salinas, Owner at Ironworks Gate Co., serving Haltom City and the surrounding DFW metro.